Toshiba tecra s4 user manual

With the hard disk drive in a vertical position, lift it straight up and away from the connector. With the connector connected, lower the hard disk drive down to the storage position.

Plastic tab Hard disk drive pack Connector Installing the hard disk drive pack 5. Seat the cover and press down until the latches click into place.

Hard disk drive Inserting the hard disk drive 3. Close the lid and slide the lock to the lock position. Page External Monitor Optional Devices External monitor An external analog monitor can be connected to the external monitor port on the computer. To connect a monitor, follow the steps below. Refer to Chapter 5, Keyboard.

Follow the steps below. Open the Control Panel and click Appearance and Themes. Page There is a possibility that the original data will be damaged.

There is a particular risk that some frames will be deleted in the case of digital video transfer. Point to i. Disconnect the cable from the computer then from the i.

LINK device. Refer also to the documentation that came with your i. Page Parallel Printer 8. Start the HW Setup program. Choose Reboot for the change to take effect. However, should problems occur, following the procedures in this chapter can help to determine the cause.

All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Page Preliminary Checklist Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem.

Page Hardware And System Checklist Before using a peripheral device or application software that is not an authorized Toshiba part or product, make sure the device or software can be used with your PC.

Use of incompatible devices may cause injury or may damage your PC. Page Self Test This message remains on the screen for a few seconds. Please contact your dealer.

Page Fully discharge the battery, then try to charge it again. Consider using a power saving mode. Page Real Time Clock 5. Press Y key. BIOS setup will terminate and the computer will be rebooted. Keyboard Keyboard problems can be caused by your setup configuration.

For more information refer to Chapter 5, Keyboard. Press gently until it clicks into place. Check whether the drive power is on. SD memory card You cannot read a file Make sure the target file is on the SD memory card inserted in the slot. If problems persist, contact your dealer. PC card Refer also to Chapter 8, Optional Page Dual Pointing Device Device tab.

Then click the Detail Setting button and click the Device Select tab. Check whether the Touch Pad is selected or not. On-screen pointer The system might be busy.

If the pointer is If the pointer is does not respond to shaped as an hourglass, wait for it to resume its mouse operation normal shape and try again to move it. Make sure the mouse is properly connected to the USB port. Make sure the USB device drivers are properly installed. Page Troubleshooting Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure.

Check Windows Device Manager. Page Troubleshooting i. LINK device does not Make sure the cable is securely connected to the function computer and to the device.

Reinstall the drivers. Page Wireless Lan Troubleshooting Problem Procedure You cannot receive an Check the rings before auto answer setting in incoming call your communications application. You can also use the ATS0 command. Page Troubleshooting Bluetooth For more information on wireless communication, refer to Chapter 4, Operating Basics.

Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on. No display Try adjusting the contrast and brightness controls on the external monitor. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.

Recharge time varies depending on usage. Battery may not charge while computer is consuming full power. Page Lcd Legal Footnotes Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology. Maximum brightness is only available when operating in AC power mode. The screen will dim when the computer is operated on battery power and you will not be able to increase the brightness of the screen.

Page Display Controller And Modes Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular parts on the screen on or off. The display controller also controls the video mode, which uses industry standard rules to govern the screen resolution and the maximum number of colors that can be displayed on screen.

The performance of PowerMizer can be configured in three ways. Page Windows Manual Setup 3. Follow the onscreen instructions to continue Windows setup. Page An effective way to ensure that such situations do not happen is to carry out RAID-1 media checks regularly. Switch on your computer while pressing the Esc key.

The Execute Creation message is displayed once the configuration is modified. Move the cursor to the appropriate location and press the space bar to continue. Pressing the Home key will revert the modified Create State settings back to the Current State settings. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.

Indication The indication shown below appears on this equipment. All cords must meet the following specifications: Length: Minimum 2 meters The settings can only be activated or modified by a user with supervisor authority. Satellite A50 Model number: e. Page Glossary Glossary The terms in this glossary cover topics related to this manual.

Alternate naming is included for reference. For example, the AC adaptor modifies the power from a wall outlet for use by the computer. Page alternating current AC : Electric current that reverses its direction of flow at regular intervals. Voice communications are analog signals. Page boot: Short for bootstrap. A program that starts or restarts the computer. Typically used to describe the data transmission speed of a modem. An electronic circuit fabricated on a silicon wafer that requires very little power.

Integrated circuits implemented in CMOS technology can be tightly packaged and are highly reliable. Page cursor: A small, blinking rectangle or line that indicates the current position on the display screen. The DVD-R drive uses a laser to read data from the disc. What is HDMI? An HDMI cable is used to transport audio and video signals between devices.

How can I best clean my Laptop? A slightly damp cleaning cloth or soft, dust-free cloth works best to remove fingerprints. Dust in hard-to-reach places is best removed with compressed air. How do I clean my keyboard? Hold the keyboard upside down and use a can of compressed air to blow away the dirt. The keys can even be cleaned with a damp cloth. See the Windows Help and Support content for more information about.

The procedure is as follows. Follow the instructions shown on the on-screen menu. While holding the F8 key, turn on the computer. The Advanced Boot Options menu will be displayed. Use the arrow keys to select Repair Your Computer and press. Follow the on-screen instructions. Depending on the model you purchased, different ways for restoring the pre-installed software are offered:. Wait for it to finish, then disable virus detection programs including any software that checks files automatically in the background.

They may cause unstable operation and damage data. You should therefore verify the optical disc drive supports the blank media you have chosen before proceeding. Turn on your computer and allow it to load the Windows 7 operating system from the hard disk drive as normal. Insert the media into the computer. After Recovery Media Creator starts, select the type of media and the title you wish to copy, and then click the Create button.

If the pre-installed files are damaged, you are able to either use the Recovery Media you have created or the hard disk drive recovery process to restore the computer to the state it was in when you originally received it. To perform this restoration, follow the steps below:. Please refer to Chapter 5, The Keyboard , for further details. When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost. Use the up and down cursor key to select the appropriate option from the menu according to your actual recovery media.

A menu will be displayed from which you should follow the on-screen instructions. To open the setup files,. A portion of the total hard disk drive space is configured as a hidden recovery partition. This partition stores files which can be used to restore pre-installed software in the event of a problem. If you subsequently set up your hard disk drive again, do not change, delete or add partitions in a manner other than specified in the manual, otherwise you may find that space for the required software is not available.

In addition, if you use a third-party partitioning program to reconfigure the partitions on your hard disk drive, you may find that it becomes impossible to setup your computer. While holding down 0 zero key on the keyboard, turn on your computer. You will receive your Recovery Discs within two weeks after placing your order. Please handle your computer carefully to avoid scratching or damaging the surface. System indicators These LED indicators allow you to monitor the status of various computer functions and are described in more detail within the System indicators section.

Refer to the. Optional devices section in Chapter 3, Hardware, Utilities and Options. Keep foreign metal objects, such as screws, staples and paper clips, out of the Bridge media slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.

Interference from a microwave oven or other source can disrupt Wi-Fi or Bluetooth operation. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction of your medical device when using any wireless functionality. Radio waves can cause malfunction of such equipment, possibly resulting in serious injury.

Please note that it is not possible to confirm the operation of all functions of all USB devices that are available. In view of this it may be noted that some functions associated with a specific device might not operate properly. Do not block the cooling vents. Keep foreign metal objects, such as screws, staples and paper clips, out of the cooling vents. ExpressCard slot This slot allows you to install a single ExpressCard device.

Provided with some models. Keep foreign metal objects, such as screws, staples and paper clips, out of the PC Card slot. Mini DisplayPort This port is capable of driving resolutions up to x Smart Card slot This slot can accommodate a single Smart Card device.

Some models are equipped with a Smart Card slot. Keep foreign metal objects, such as screws, staples and paper clips, out of the Smart Card slot. Headphone jack A 3. Microphone jack A 3. Keep foreign metal objects, such as screws, staples and paper clips, out of the USB connectors.

It could cause damage or malfunction. There may be a remote risk of electric shock from lightning. The following figure shows the underside of the computer. You should ensure that the display is closed before the computer is turned over to avoid causing any damage. Chapter 3, Hardware, Utilities and Options. Do not attempt to use any other Port Replicator. Refer to the Additional memory module section in.

This section shows the computer with the display panel open. In order to open the display, lift the display panel up and position it at a comfortable viewing angle for you. LCD Sensor switch not shown. Touch Pad control buttons. Bluetooth antenna not shown. Figure The front of the computer with the display panel open A4 size keyboard. Chapter 4, Operating Basics.

For example, when you close the display panel the computer enters Hibernation Mode and shuts itself down and then, when you next open the display, the computer will automatically start up and return you to the application you were previously working on. You can specify within the Power Options. Do not put any magnetic objects close to this switch as they may cause the computer to automatically enter Hibernation Mode and shut down even if the Panel Power Off feature is disabled.

LED system indicators next to their respective icons, glow when specific computer operations are in progress. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Tecra S Disclaimer This manual has been validated and reviewed for accuracy. Network Compatibility Statement This product is designed to work with, and is compatible with the following networks.

Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Abbreviations On first appearance, and whenever necessary for clarity, abbreviations are enclosed in parentheses following their definition.

Icons Icons identify ports, dials, and other parts of your computer. Key operation Some operations require you to simultaneously use two or more keys. Display S Names of windows or icons or text generated by the ABC computer that appear on its display screen are presented in the type face you see to the left. Messages Messages are used in this manual to bring important information to your attention. Creating a computer-friendly environment Place the computer on a flat surface that is large enough for the computer and any other items you are using, such as a printer.

ExpressCard overheating Some ExpressCards can become hot during prolonged use which may result in errors or instability in the operation of the device in question. Mobile phones Please be aware that the use of mobile phones can interfere with the audio system. Equipment checklist Carefully unpack your computer, taking care to save the box and packaging materials for future use.

Connect the power cord to the AC adaptor. DC IN 15V jack 2. Display panel Figure Opening the display panel Use reasonable care when opening and closing the display panel.

Open the display panel. Power button Figure Turning on the power Starting up for the first time The Windows 7 Startup Screen will be the first screen displayed when you turn on the power. Sleep Mode If you have to interrupt your work, you are able to turn off the power without exiting from your software by placing the computer into Sleep Mode. Hibernation Mode The Hibernation Mode feature saves the contents of memory to the hard disk drive when the computer is turned off so that, the next time it is turned on, the previous state is restored.

Point to the arrow icon and then select Hibernate from the menu. Automatic Hibernation Mode The computer can be configured to enter Hibernation Mode automatically when you press the power button or close the lid. In order to define these settings, you can follow the steps as described below: 1. Data save in Hibernation Mode When you turn off the power in Hibernation Mode, the computer will take a moment to save the current data in memory to the hard disk drive. System Recovery Options and Restoring the pre-installed software There is a hidden partition allocated on the hard disk drive for the System Recovery Options.

System Recovery Options The System Recovery Options feature is installed on the hard disk when shipped from the factory. The System Recovery Options can also be run manually to repair problems. Turn off the computer. Restoring the pre-installed software from the Recovery hard disk drive A portion of the total hard disk drive space is configured as a hidden recovery partition. Turn off your computer. System indicators 4. Bridge media slot 5.

Stereo speakers 3. Figure Front of the computer with display panel closed System indicators These LED indicators allow you to monitor the status of various computer functions and are described in more detail within the System indicators section. Stereo speakers The speakers emit sound generated by your software as well as audio alarms, such as low battery condition, generated by the system.

Microphone A built-in microphone allows you to import and record sounds to your application - please refer to the Sound System section in Chapter 4, Operating Basics , for more information.

Some models are equipped with a built-in microphone. Cooling vents 4. Cooling vents The cooling vents help keep the processor from overheating. Headphone jack 3. Microphone jack 4. Security lock slot 5. External monitor port 6. LAN jack 3. LAN active indicator orange 4. DC IN 15V jack 8. Figure The back side of the computer Security lock slot A security cable can be attached to this slot and then connected to a desk or other large object in order to deter theft of the computer.

External monitor This port provides pin, analog VGA port.